- TechToolsList - listserv.classicarcade.com

Fluke 68000 Pod Problem
by Theron Troxel via Techtoolslist 06 Jul '15

06 Jul '15

Just got a 68000 and tried to self-test and comes back with "POD SELF TEST 68000 FAIL 00". Any help with this error? Also, does anyone fix Fluke Pods? _______________________________________________ Techtoolslist mailing list Techtoolslist(a)flippers.com https://pairlist7.pair.net/mailman/listinfo/techtoolslist FTP site is: ftp://ttl.arcadetech.org/TTL/Test_Equipment Archive site: http://seven.pairlist.net/pipermail/techtoolslist/

4 4

ROM Sigs the same on 9010 and 9100A ?
by Andre Huijts 24 Jun '15

24 Jun '15

Maybe a stupid question but are the “Fluke Sigs” supposed to be the same on the 9010 and 9100A ? Or do they produce different SIGs ? Thanks, André André Huijts andre.huijts(a)upcmail.nl _______________________________________________ Techtoolslist mailing list Techtoolslist(a)flippers.com https://pairlist7.pair.net/mailman/listinfo/techtoolslist FTP site is: ftp://ttl.arcadetech.org/TTL/Test_Equipment Archive site: http://seven.pairlist.net/pipermail/techtoolslist/

4 5

Kurz-Kasch #300 Rockola docs needed
by John Robertson 18 Jun '15

18 Jun '15

Anyone have the documents for the Rockola test set #300? I'd appreciate a scan and I'll put it up on my KK page on flippers too. Thanks! John :-#)# -- How to subscribe or unsubscribe from TTL http://seven.pairlist.net/mailman/listinfo/techtoolslist _______________________________________________ Techtoolslist mailing list Techtoolslist(a)flippers.com https://pairlist7.pair.net/mailman/listinfo/techtoolslist FTP site is: ftp://ttl.arcadetech.org/TTL/Test_Equipment Archive site: http://seven.pairlist.net/pipermail/techtoolslist/

1 0

9100FT
by Andrew Welburn 05 Jun '15

05 Jun '15

long shot.. But has anyone seen, or knows of a service disk suitable for the 9100FT ? I'm updating my 9100 page soon as i've been working on 5 of these systems, but while i can set the 9100FT to acknowledge 16mb ram in post, the system always reports just 4mb.. I can actually get it to test 32mb (when installed 8x4mb) but the post always fails, and the dip switch combination is not even valid as per what is screened on the pcb. I dont think they ever anticipated any crazy person putting in 32mb ram and just abandoned compatability :) the v1.4 service disk is the latest version i have, but it only allows you to set 1,2 or 4mb system ram... any ideas? -- Andrew Welburn http://www.andys-arcade.com _______________________________________________ Techtoolslist mailing list Techtoolslist(a)flippers.com http://seven.pairlist.net/mailman/listinfo/techtoolslist FTP site is: ftp://ttl.arcadetech.org/TTL/Test_Equipment Archive site: http://seven.pairlist.net/pipermail/techtoolslist/

4 11

Fluke 9100FT Service disk
by Steve Larkins 01 Jun '15

01 Jun '15

Hello all, Please please please can someone supply an image of the V1.6 service disk. We have V1.4 but this doesn't help with some aspects of the 9100ft such as maximum memory. Who ever can you will be king! Cheers Steve _______________________________________________ Techtoolslist mailing list Techtoolslist(a)flippers.com https://pairlist7.pair.net/mailman/listinfo/techtoolslist FTP site is: ftp://ttl.arcadetech.org/TTL/Test_Equipment Archive site: http://seven.pairlist.net/pipermail/techtoolslist/

3 2

Re: [Techtoolslist] leland off road pal dump needed u85
by Gary M. McTaggart 08 May '15

08 May '15

If you have your adapter, I can get a chip to you for the track pack Clay. I was in Portland yesterday. Wish I would had known then. :) I can mail you the chip for the track pack. Otherwise I can use my rom burner to read it, but that may take longer for me to get to. > On Mar 17, 2015, at 12:32 AM, Clay Cowgill <c.cowgill(a)comcast.net> wrote: > > I might still have the exact adapter. I'll look for it Tuesday and report > back here... I can take a few pictures of it. (I might even have a Track > Pack boardset and could just read the PROM in here. I don't remember what's > our machine in storage. I'll look. If nothing else, if our PCB is the > original one just reading and duplicating that would serve as a proof of > concept.) > > OE&CE can just be disconnected. Looking at the schematics all the outputs > are going to be push/pull (no tristate), so nothing 'special' required to > brute-force the dump. (Also, two outputs are not even used.) > > -Clay > > -----Original Message----- > From: Techtoolslist [mailto:techtoolslist-bounces@flippers.com] On Behalf Of > tonyhtbsusa > Sent: Monday, March 16, 2015 6:17 PM > To: 'Technical Tools Mail List' > Subject: Re: [Techtoolslist] leland off road pal dump needed u85 > > Do you have a pinout of how you did it > Did you go from pin one to pin one > Did it matter what address line or data line went to what pin on eprom The > 2716 starts at address 7 on pin 1 And data lines are split From side to side > What did you do with /oe or /ce Thanks tony > > _______________________________________________ > Techtoolslist mailing list > Techtoolslist(a)flippers.com > https://pairlist7.pair.net/mailman/listinfo/techtoolslist > FTP site is: ftp://ttl.arcadetech.org/TTL/Test_Equipment > Archive site: http://seven.pairlist.net/pipermail/techtoolslist/ _______________________________________________ Techtoolslist mailing list Techtoolslist(a)flippers.com https://pairlist7.pair.net/mailman/listinfo/techtoolslist FTP site is: ftp://ttl.arcadetech.org/TTL/Test_Equipment Archive site: http://seven.pairlist.net/pipermail/techtoolslist/

5 10

Anybody have a simple/cheap way?
by William Stillwell 25 Apr '15

25 Apr '15

To plug a Fluke pod with a pga package to a board with PLCC ? ie, PGA68 -> PLCC68 ? ( in this case a 80186 ) William Stillwell Hamster / KI4SWY Stillwell Software Solutions. Free Play Florida Arcade & Pinball Show Organizer _______________________________________________ Techtoolslist mailing list Techtoolslist(a)flippers.com https://pairlist7.pair.net/mailman/listinfo/techtoolslist FTP site is: ftp://ttl.arcadetech.org/TTL/Test_Equipment Archive site: http://seven.pairlist.net/pipermail/techtoolslist/

2 2

KK-6502-A NOP Atari Compatible
by teeray 15 Apr '15

15 Apr '15

I know how to make one of these that will give Address bus signatures that match the Z80 sigs and will match all of the Atari documentation sigs but I would like to know the real opcode that Kurz-Kasch used for this NOP (data bus wiring) If you can help please let me know. Thanks Tim _______________________________________________ Techtoolslist mailing list Techtoolslist(a)flippers.com https://pairlist7.pair.net/mailman/listinfo/techtoolslist FTP site is: ftp://ttl.arcadetech.org/TTL/Test_Equipment Archive site: http://seven.pairlist.net/pipermail/techtoolslist/

2 1

Kurz Kasch Intelligent NOP
by teeray 11 Apr '15

11 Apr '15

OK what about Kurz-Kasch Intelligent NOP's anyone have one of these? _______________________________________________ Techtoolslist mailing list Techtoolslist(a)flippers.com https://pairlist7.pair.net/mailman/listinfo/techtoolslist FTP site is: ftp://ttl.arcadetech.org/TTL/Test_Equipment Archive site: http://seven.pairlist.net/pipermail/techtoolslist/

1 0

Kurz Kasch Programmable NOP
by teeray 11 Apr '15

11 Apr '15

>From what I understand they have a DIP switch that allows setting the data bus lines Looks like they made a 6502, Z80, 6800 and 8080 Programmable NOP's Anyone have one of these ? Thanks Tim _______________________________________________ Techtoolslist mailing list Techtoolslist(a)flippers.com https://pairlist7.pair.net/mailman/listinfo/techtoolslist FTP site is: ftp://ttl.arcadetech.org/TTL/Test_Equipment Archive site: http://seven.pairlist.net/pipermail/techtoolslist/

1 0