January 2012 - TechToolsList - listserv.classicarcade.com

Re: [Techtoolslist] Fluke on Mario Bros.
by David Shoemaker 20 Apr '18

20 Apr '18

Looking at the manual for the Z80QT pod and the schematic I think I am getting an expected result. I hooked up the pod and hit BUS to run the bus test. I immediately get back CTL ERR showing 00000010 this is the HALT line. Looking at the schematic it appears HALT and INT are both tied together and pulled high. So the fluke can't exercise that line. Any way to ignore that error and verify the rest of the bus test? Oh and according the manual maximum clock frequency is 8.0 mhz. Does that mean this pod support Z80A/B/C ? From: David Shoemaker [mailto:davids@oz.net] Sent: Wednesday, November 16, 2011 10:38 PM To: 'Technical Tools Mail List' Subject: Fluke on Mario Bros. Anyone know if you can use either the base z80 pod or the z80qt pod on Mario bros? I know it uses the Z80A but I don't know what the pod is rated at. Thanks, David _______________________________________________ Techtoolslist mailing list Techtoolslist(a)flippers.com http://seven.pairlist.net/mailman/listinfo/techtoolslist FTP site is: ftp://ftp.flippers.com/TTL/TestEquipment Archive site: http://seven.pairlist.net/pipermail/techtoolslist/

4 7

Fluke 9000A mystery adapter (for me at least ;-)
by John Robertson 20 Feb '18

20 Feb '18

I have a pod module here called "Z8 I/F ADAPTER" Fluke #9000-200/AB. It has no cable to the base, just a 40 pin CPU cable. Inside is a couple of RAM chips, and some Fluke hybrid interface ICs. Any guesses? John :-#)#

3 7

Any Taito Bench Tester documentation available?
by James Marous 04 Feb '14

04 Feb '14

6 15

Re: Cracking the 9010A ROM signature generator
by Kev 02 Feb '13

02 Feb '13

2 3

Fluke 9000a-8051 Manual
by Ed Osborne 10 Sep '12

10 Sep '12

7 14

Test rig I picked up today
by Ness and Steve 31 Jan '12

31 Jan '12

Hello all, I picked up the following test rig today: http://www.poachersrope.co.uk/testequipment/testrig/MHG/ It's pretty cool and looks like it is geared towards Atari games. It is stamped with MHG test unit which I have been told by a reliable source(Cheers Andy Welburn) was a huge UK based distributor. It would appear to cater for Vector and Raster in both colour and black and white. I have a few adapters but I suspect I am going to have to buzz out the connectors and give it a serious clean. Has anyone seen anything similar to this before? It looks very well made. Cheers Steve _______________________________________________ Techtoolslist mailing list Techtoolslist(a)flippers.com http://seven.pairlist.net/mailman/listinfo/techtoolslist FTP site is: ftp://ftp.flippers.com/TTL/TestEquipment Archive site: http://seven.pairlist.net/pipermail/techtoolslist/

3 2

Fluke 9100A/FT SMPS fault
by Ness and Steve 29 Jan '12

29 Jan '12

Hello All, My fluke 9100ft has developed a PSU fault that causes the mains to my work shop to trip after around 3 minutes when turned on. I have completely disconnected all outputs rails and bypassed the input filter and it does the same. So I have 2 options. 1. Repair the SMPS 2. Buy a replacement SMPS Has anyone had similar problems. Does anyone have a spare SMPS? Cheers Steve _______________________________________________ Techtoolslist mailing list Techtoolslist(a)flippers.com http://seven.pairlist.net/mailman/listinfo/techtoolslist FTP site is: ftp://ftp.flippers.com/TTL/TestEquipment Archive site: http://seven.pairlist.net/pipermail/techtoolslist/

3 2

Trade a z80 for a 6809?
by David Shoemaker 28 Jan '12

28 Jan '12

I have a spare z80 pod (passes all self-test) and could use a 6809. Anyone interested in a trade? David _______________________________________________ Techtoolslist mailing list Techtoolslist(a)flippers.com http://seven.pairlist.net/mailman/listinfo/techtoolslist FTP site is: ftp://ftp.flippers.com/TTL/TestEquipment Archive site: http://seven.pairlist.net/pipermail/techtoolslist/

1 0

Ram tests on Robotron with 9010
by David Shoemaker 23 Jan '12

23 Jan '12

3 2