August 2012 - TechToolsList - listserv.classicarcade.com

Re: [Techtoolslist] Fluke on Mario Bros.
by David Shoemaker 20 Apr '18

20 Apr '18

Looking at the manual for the Z80QT pod and the schematic I think I am getting an expected result. I hooked up the pod and hit BUS to run the bus test. I immediately get back CTL ERR showing 00000010 this is the HALT line. Looking at the schematic it appears HALT and INT are both tied together and pulled high. So the fluke can't exercise that line. Any way to ignore that error and verify the rest of the bus test? Oh and according the manual maximum clock frequency is 8.0 mhz. Does that mean this pod support Z80A/B/C ? From: David Shoemaker [mailto:davids@oz.net] Sent: Wednesday, November 16, 2011 10:38 PM To: 'Technical Tools Mail List' Subject: Fluke on Mario Bros. Anyone know if you can use either the base z80 pod or the z80qt pod on Mario bros? I know it uses the Z80A but I don't know what the pod is rated at. Thanks, David _______________________________________________ Techtoolslist mailing list Techtoolslist(a)flippers.com http://seven.pairlist.net/mailman/listinfo/techtoolslist FTP site is: ftp://ftp.flippers.com/TTL/TestEquipment Archive site: http://seven.pairlist.net/pipermail/techtoolslist/

4 7

Fluke 9000A mystery adapter (for me at least ;-)
by John Robertson 20 Feb '18

20 Feb '18

I have a pod module here called "Z8 I/F ADAPTER" Fluke #9000-200/AB. It has no cable to the base, just a 40 pin CPU cable. Inside is a couple of RAM chips, and some Fluke hybrid interface ICs. Any guesses? John :-#)#

3 7

Any Taito Bench Tester documentation available?
by James Marous 04 Feb '14

04 Feb '14

6 15

Re: Cracking the 9010A ROM signature generator
by Kev 02 Feb '13

02 Feb '13

2 3

Fluke 9000a-8051 Manual
by Ed Osborne 10 Sep '12

10 Sep '12

7 14

Kurz-Kasch adapters
by Andrew Welburn 26 Aug '12

26 Aug '12

hi all... My friend has happened upon a large number of KK adapters, is anyone actively looking for these? -- Andrew Welburn http://www.andys-arcade.com _______________________________________________ Techtoolslist mailing list Techtoolslist(a)flippers.com http://seven.pairlist.net/mailman/listinfo/techtoolslist FTP site is: ftp://ttl.arcadetech.org Archive site: http://seven.pairlist.net/pipermail/techtoolslist/

3 2

http://tech.quarterarcade.com/tech/ not finding games?
by David Shoemaker 12 Aug '12

12 Aug '12

I was trying to get fluke signatures for pac man. I went to the quarterarcade site and it appears to have a problem with looking up mame images. No matter what I enter I always get back no game found. Anyone else able to get it working? Thanks, David _______________________________________________ Techtoolslist mailing list Techtoolslist(a)flippers.com http://seven.pairlist.net/mailman/listinfo/techtoolslist FTP site is: ftp://ttl.arcadetech.org Archive site: http://seven.pairlist.net/pipermail/techtoolslist/

1 0

Disable watchdog on pacman?
by David Shoemaker 11 Aug '12

11 Aug '12

I am trying to use the fluke on a pacman board and want to disable the watchdog. Anyone have a simple way of doing so on these boards? Thanks, David _______________________________________________ Techtoolslist mailing list Techtoolslist(a)flippers.com http://seven.pairlist.net/mailman/listinfo/techtoolslist FTP site is: ftp://ttl.arcadetech.org Archive site: http://seven.pairlist.net/pipermail/techtoolslist/

2 1

Dummy load on power supply
by David Shoemaker 08 Aug '12

08 Aug '12

I am testing a board that takes 12v in. I am using a Peter Chau supply on my bench. As the voltages follow 5v on those I need to load the supply somewhat to stabilize Is 1A enough? Thanks, David _______________________________________________ Techtoolslist mailing list Techtoolslist(a)flippers.com http://seven.pairlist.net/mailman/listinfo/techtoolslist FTP site is: ftp://ttl.arcadetech.org Archive site: http://seven.pairlist.net/pipermail/techtoolslist/

3 4

Atari CTF-1
by Andrew Welburn 07 Aug '12

07 Aug '12

Calling out for anyone (but probably just aimed at John ;) who might have paperwork/schems for the CTF-1.. I spent a good little while hunting online and can't find anything... I have my CTF-1 on the bench now, and i'm trying to repurpose it, or at least work out how much of it is missing, needs replacing or what i need to be hunting for. Right now i need to use the variacs in my own rig, so i'll proabably end up with a Franken-rig of sorts for now, but i need to get working on it. here's my rig right now : http://www.andysarcade.net/personal/bronzeage/CTF-1/CTF6aug12.JPG here's my webpage documenting its restoration: http://www.andysarcade.net/personal/bronzeage/CTF-1/ any help appreciated, wiring diagram especially wanted..! -- Andrew Welburn http://www.andys-arcade.com _______________________________________________ Techtoolslist mailing list Techtoolslist(a)flippers.com http://seven.pairlist.net/mailman/listinfo/techtoolslist FTP site is: ftp://ttl.arcadetech.org Archive site: http://seven.pairlist.net/pipermail/techtoolslist/

2 5