- TechToolsList - listserv.classicarcade.com

Re: [Techtoolslist] Galaga '88 (GaPlus) Color PROM binaries
by Tony Gonzalez 13 May '05

13 May '05

Try getting the MAME images, it sohuld be in there... Tony --- Bill Karkula <wkarkula(a)comcast.net> wrote: > Hello - I'm repairing a Galaga '88 and one of the > color proms may be bad. > I'm not having much luck locating the binaries for > the four small bipolar > proms on the board. > > Any help is appreciated. > > Thank You and Best Regards, > > Bill > > > > _______________________________________________ > Techtoolslist mailing list > Techtoolslist(a)flippers.com > http://seven.pairlist.net/mailman/listinfo/techtoolslist > __________________________________________________ Do You Yahoo!? Tired of spam? Yahoo! Mail has the best spam protection around http://mail.yahoo.com _______________________________________________ Techtoolslist mailing list Techtoolslist(a)flippers.com http://seven.pairlist.net/mailman/listinfo/techtoolslist

1 0

Galaga '88 (GaPlus) Color PROM binaries
by Bill Karkula 13 May '05

13 May '05

Hello - I'm repairing a Galaga '88 and one of the color proms may be bad. I'm not having much luck locating the binaries for the four small bipolar proms on the board. Any help is appreciated. Thank You and Best Regards, Bill _______________________________________________ Techtoolslist mailing list Techtoolslist(a)flippers.com http://seven.pairlist.net/mailman/listinfo/techtoolslist

1 0

Sencore X18 Adapter for CR31 Rejuvenator
by Mark Hooks 05 May '05

05 May '05

2 1

Replacing a Fluke 9100a disk drive
by Chris Hardy 03 May '05

03 May '05

I finally need to replace the faulty disk drive in my 9100a as I need to install the newer software. The drive thats currently in there is a double density Cannon MD350. The service manual has the jumper settings for drive 0 and drive 1, and strangely you have change two jumpers instead of just the ID. (but there is no documentation of what these actual jumpers are for, either on the net or in the manual) I've tried using a std pc 1.44meg floppy drive, changing the drive ID to be ID0 like the original drive, and also tried 2 std amiga double density drives but neither want to work. The original drive is definately faulty as the fluke can't format a disk, and won't read the original software regardless of if it's a high or double density disk. I suspect I need to change some of the jumpers on a std drive to handle the different drive selects and the way the motors are enabled but have failed to find any info on the net about this. Any help would be appreciated Chris _______________________________________________ Techtoolslist mailing list Techtoolslist(a)flippers.com http://seven.pairlist.net/mailman/listinfo/techtoolslist

3 4

Fluke 9100a Utility Service Disk Ver 1.4
by AL SACCO_comcast 01 May '05

01 May '05

1 0

FS: Amplifone HVU (working)
by Electronicamuse＠aol.com 30 Apr '05

30 Apr '05

1 0

Fluke 9100a X2444 question
by AL SACCO_comcast 26 Apr '05

26 Apr '05

4 10

RE: [Techtoolslist] Spy Hunter Cheap Squeak Wiring?
by Anthony Pietrak 26 Apr '05

26 Apr '05

Actually, I've got that covered, I have a switching power supply running along with Tom W's MCR adapter kit. Pretty sure the reset signal is hooked up to the Cheap Squeak, but I'll double check. Anthony --Anthony Pietrak www.QuarterArcade.com Restored Arcade Games for your Home > -----Original Message----- > From: Chris Hardy [mailto:chris@hardys.plus.com] > Sent: Tuesday, April 26, 2005 12:45 PM > To: anthony(a)quarterarcade.com; Technical Tools Mail List > Subject: Re: [Techtoolslist] Spy Hunter Cheap Squeak Wiring? > > > The PSU supplies a reset pulse to the game board and the > cheap squeak music > board. > > You can get around this by manually connecting the reset pin > on the cheap > squeak to +5v ( or was it ground, I don't recall) > > Either way, you cant just get away with tying the line to +5v > (or ground), > it has to be a pulse > > Chris > > (had me going for quite a while the last time I fixed a Spy > Hunter sound > board) > > ----- Original Message ----- > From: "Anthony Pietrak" <anthony(a)quarterarcade.com> > To: <techtoolslist(a)flippers.com> > Sent: Tuesday, April 26, 2005 5:17 PM > Subject: [Techtoolslist] Spy Hunter Cheap Squeak Wiring? > > > _______________________________________________ Techtoolslist mailing list Techtoolslist(a)flippers.com http://seven.pairlist.net/mailman/listinfo/techtoolslist

1 0

Spy Hunter Cheap Squeak Wiring?
by Anthony Pietrak 26 Apr '05

26 Apr '05

Been putting together a test bench for Spy Hunter boards and I'm having a problem with the Cheap Squeak wiring. I've been able to get good video, rigged up some controls and have the non-music sounds working, but can't get any music. I've noticed in the wiring diagram that the lamp driver board has some connections to the Cheap Squeak. Does the lamp driver board have to be connected and working to get music? Any other simple things I could be missing? Thanks, Anthony --Anthony Pietrak www.QuarterArcade.com Restored Arcade Games for your Home _______________________________________________ Techtoolslist mailing list Techtoolslist(a)flippers.com http://seven.pairlist.net/mailman/listinfo/techtoolslist

1 0

sega outrun stuck in reset
by tony 25 Apr '05

25 Apr '05

6 9