- TechToolsList - listserv.classicarcade.com

Benchmate 400 Manual?
by James Marous 03 Aug '05

03 Aug '05

1 0

Re: [Techtoolslist] What rejuvenator adapters need to be made?
by Electronicamuse＠aol.com 02 Aug '05

02 Aug '05

1 0

What rejuvenator adapters need to be made?
by Electronicamuse＠aol.com 02 Aug '05

02 Aug '05

2 1

Signatures
by Martin White 26 Jul '05

26 Jul '05

Don't suppose there's any known formulae or program to convert HP / Catbox sigs to Fluke sigs and vice versa is there? Not a big deal but i have some fluke sigs that would be easier to convert than resample... Martin. _______________________________________________ Techtoolslist mailing list Techtoolslist(a)flippers.com http://seven.pairlist.net/mailman/listinfo/techtoolslist

1 0

fluke z8002 48-40 pin adapter pole position
by tony 14 Jul '05

14 Jul '05

2 1

Re: Atari Cat box in the UK
by Phil Mayor 07 Jul '05

07 Jul '05

1 0

Poss. dumb 9010 query
by Martin White 07 Jul '05

07 Jul '05

Sorry, but i do get rather confused with this thing from time to time :o) I'm getting a "R/W Error @ F800 BTS 08" when trying to test the ram on one of these MCR boards. Am i right in saying that i need to be tracking down a problem on the data bus, bit 4, bit 3 if you prefer your numbers to be 0 based (1000 = 8, therefore, that's bit 0, 1, 2, then 3 or 1, 2, 3, then 4). And if it were a decode error then that would be the address bus? I'm assuming all is well with chip selects and r/w signals since it's only complaining about bit 08 and not FF? As an aside, i burnt a set of home burnt roms but the 9010 still can't read the things reliably in the MCR sets. It doesn't seem to like anything that's in close relation to the CTC i don't think. It's happy enough troubleshooting the video staging ram and the background ram, just not the program ram or rom :( I'm using a normal Z80 pod with a Z80A processor in it. I'm guessing from reading previous posts that there would be no benefit in trying to blag or borrow a Z80AA since someone else was saying that couldn't cope with MCR hardware either. Martin. _______________________________________________ Techtoolslist mailing list Techtoolslist(a)flippers.com http://seven.pairlist.net/mailman/listinfo/techtoolslist

2 3

Data I/O 29A to Windows XP Data Transfer
by Mark Hooks 06 Jul '05

06 Jul '05

4 6

FS: Atari Cat box in the UK
by Phil Mayor 06 Jul '05

06 Jul '05

1 0

Missle Command Help
by Bill Karkula 04 Jul '05

04 Jul '05

I worked on four Missle commands for the first time and got three of them working (what a design - not designed for easy hardware debugging). The fourth board has me stymied. It comes up with one high beep for one of the 4116s being bad which I have replaced twice but the error still comes up. If I intentionally remove any other drams the correct beep error is caught. I've checked continuity to the suspect Dram but all is fine. I've gone over all of the sections of the board and they all seem to be working but the board as a system won't come up. It just keeps looping the dram beeping test. Any suggestions based upon your collective experience would be welcome. Thank You and Best Regards, Bill _______________________________________________ Techtoolslist mailing list Techtoolslist(a)flippers.com http://seven.pairlist.net/mailman/listinfo/techtoolslist

5 5