- TechToolsList - listserv.classicarcade.com

Re: [Techtoolslist] Kurz-Kasch TC-590-89 Test Clip
by teeray 23 Feb '13

23 Feb '13

-----Original Message----- >From: John Robertson <jrr(a)flippers.com> >Sent: Feb 22, 2013 7:42 PM >To: Technical Tools Mail List <techtoolslist(a)flippers.com> >Subject: Re: [Techtoolslist] Kurz-Kasch TC-590-89 Test Clip > >teeray wrote: >> Anyone know how a Kurz-Kasch TC-590-89 Test Clip is wired ? >> All I can find says it should have three test clips E4, B3, D3 >> >> Thanks >> Tim >> >> _ > > >These are part of the KK signature kit for 8080 boards. TC-590-89 is >basically a 16 pin Glomper clip with jumpers: > >Part "EE Module" is a 40 pin header box that have only one jumper >between pins 14, 16 & 24. >Part "B-3" and "D-3" are a 16-pin glomper clips that each (identical) >have jumpers between pins 3, 6, 8, 10, & 13. >Part "E-3" is a 16-pin glomper clips that have a jumper between pins 1 & 7. > >These four parts are used with KKs docs on using the Sig Analyzer on the >8080 boards and go on the corresponding IC (IC B-3, D-3, and E-3). > >Hope this helps! > >John :-#)# >_______________________________________________ >Techtoolslist mailing list >Techtoolslist(a)flippers.com >http://seven.pairlist.net/mailman/listinfo/techtoolslist >FTP site is: ftp://ttl.arcadetech.org/TTL/Test_Equipment >Archive site: http://seven.pairlist.net/pipermail/techtoolslist/ Big help Thanks! So on the EE Module all the pins feed through including the ones jumpered ? I ask because pin 19 would be pulled low by clip E3 and it is an output from CPU Clip E3 would cause the data bus direction to go output only (which is OK for the Midway 8080 board) and clip B3, D3 would set the 8080 to execute NOP's Thanks _______________________________________________ Techtoolslist mailing list Techtoolslist(a)flippers.com http://seven.pairlist.net/mailman/listinfo/techtoolslist FTP site is: ftp://ttl.arcadetech.org/TTL/Test_Equipment Archive site: http://seven.pairlist.net/pipermail/techtoolslist/

2 1

Kurz-Kasch TC-590-89 Test Clip
by teeray 23 Feb '13

23 Feb '13

Anyone know how a Kurz-Kasch TC-590-89 Test Clip is wired ? All I can find says it should have three test clips E4, B3, D3 Thanks Tim _______________________________________________ Techtoolslist mailing list Techtoolslist(a)flippers.com http://seven.pairlist.net/mailman/listinfo/techtoolslist FTP site is: ftp://ttl.arcadetech.org/TTL/Test_Equipment Archive site: http://seven.pairlist.net/pipermail/techtoolslist/

2 1

Todays try
by David Shoemaker 21 Feb '13

21 Feb '13

Just a test to see if mail will go through for me. _______________________________________________ Techtoolslist mailing list Techtoolslist(a)flippers.com http://seven.pairlist.net/mailman/listinfo/techtoolslist FTP site is: ftp://ttl.arcadetech.org/TTL/Test_Equipment Archive site: http://seven.pairlist.net/pipermail/techtoolslist/

1 0

Data io 29a with Unipak
by Jose Luiz Martins 21 Feb '13

21 Feb '13

Hi folks ! About 6-7 years since my last post here... My life changed a lot, and now I'm back to Video Game world. Many years ago I bought one Data IO 29a with Unipak from ebay and left boxed since them. Last weekend I've decided to put it working and I'm facing the following error: 70 Faulty BIT supply. Any clue on that error ? Thanks, JL _______________________________________________ Techtoolslist mailing list Techtoolslist(a)flippers.com http://seven.pairlist.net/mailman/listinfo/techtoolslist FTP site is: ftp://ttl.arcadetech.org/TTL/Test_Equipment Archive site: http://seven.pairlist.net/pipermail/techtoolslist/

2 3

Re: [Techtoolslist] RASTER: FW: Using 8080 pod on Midway 8080 boards (Space Invaders)
by John Robertson 18 Feb '13

18 Feb '13

David Shoemaker wrote: > > So my mails to tech tools don't appear to be getting through. But this > is a raster game so I will cross the stream. > > > > *From:* David Shoemaker [mailto:davids@oz.net] > *Sent:* Saturday, February 16, 2013 12:20 AM > *To:* 'Technical Tools Mail List' > *Subject:* Using 8080 pod on Midway 8080 boards? > > > > I have a fully working space invaders board which when I hook the pod > up to and do Run UUT doesn't, it starts up and crashes. > > > > Pod passes self test. > > > > Anyone ever done this? > > > > David > Try a faster 8080 CPU in the pod, or try substituting the 8080 from the game in place of the pod CPU. It is possible the CPU is bad or slower than the system can handle. Do you have the flat ribbon cable from the pod to the CPU socket or the twisted pair cable? The twisted pair cable handles noise better and will work in situations when the simple flat cable won't, plus it can be longer as a result. David, I have no idea why this did not show up in TTL - you are subscribed under the same email address as you posted here. I haven't seen any bounces for your email address. John :-#)# _______________________________________________ Techtoolslist mailing list Techtoolslist(a)flippers.com http://seven.pairlist.net/mailman/listinfo/techtoolslist FTP site is: ftp://ttl.arcadetech.org/TTL/Test_Equipment Archive site: http://seven.pairlist.net/pipermail/techtoolslist/

1 0

Re: [Techtoolslist] RASTER: M2716A-2F1 datasheet
by Matthew Rossiter 15 Feb '13

15 Feb '13

So, in continuing this discussion on techtoolslist - I found that I was only about to program a couple more 2716a's and the rest failed. Then I realized that sometimes I had to program them two or three times until they finally verified correctly. Has anyone else run into this issue? Matt On 1/31/2013 10:16 AM, Matthew Rossiter wrote: > Oh Boy. Ok - so these all passed the blank check when they arrived. > But I thought, what the heck I'll run them through the UV eraser just > to make sure they're blank. Now I can program them. > > As Gilda Radner would say - Nevermind. > > Matt > > > > > On 1/31/2013 9:51 AM, Matthew Rossiter wrote: >> Well fortunately, these eproms have 21V written on the top of them so >> it's not hard to miss. I'm using a Dataman-48Pro+ where they give >> you the specs of a generic 2716A and yes it's set to program at >> 21v. I'm not sure if there's anything special about STMicro's. >> Normally what I do is try to find the datasheet, send it over to >> Dataman and they usually fix the problem. But I can't find a >> datasheet anywhere on the net. >> >> There's also the possibility I have some bad devices. :| I only >> did a quick search but I don't think the Data IO 29B does them >> either. I'll double check. I'd love to find a datasheet though. >> >> Matt >> >> On 1/31/2013 9:27 AM, John Robertson wrote: >>> Rodger Boots wrote: >>>> >>>> BE CAREFUL, 2716s program using 25 volts but what you have uses 21 >>>> volts. >>>> >>>> On Jan 31, 2013 12:16 AM, "Matthew Rossiter" <matt(a)rossiters.com >>>> <mailto:matt@rossiters.com>> wrote: >>>> >>>> Does anyone have the datasheet for the ST Microelectronics eprom >>>> M2716A-2F1? I bought them from Jameco but I can't seem to program >>>> them. They are fast 200ns eproms. >>>> >>>> Matt >>>> >>> >>> Programming a 21V 2716A (that is what the "A" means) on a 25V >>> programmer will normally destroy the Eprom. This is also the >>> difference between the 2732 (25V) and 2732A (21V). >>> >>> If you can't find the exact manufacturer and part number on your >>> list of Eproms that came with your programmer then you MUST find out >>> exactly what the device needs and then determine what Eprom is >>> closest to it so that its algorithm will work before attempting to >>> program it. the devices from the 70s were very particular about >>> voltages and timings, devices from the mid-80s and later usually to >>> have code inside them that the programmer can recognize to figure >>> out the programming voltage(s) required. >>> >>> >>> John :-#(# >>> -- >>> John's Jukes Ltd. 2343 Main St., Vancouver, BC, Canada V5T 3C9 >>> Call (604)872-5757 or Fax 872-2010 (Pinballs, Jukes, VideoGames) >>> www.flippers.com >>> "Old pinballers never die, they just flip out" >> > _______________________________________________ Techtoolslist mailing list Techtoolslist(a)flippers.com http://seven.pairlist.net/mailman/listinfo/techtoolslist FTP site is: ftp://ttl.arcadetech.org/TTL/Test_Equipment Archive site: http://seven.pairlist.net/pipermail/techtoolslist/

4 4

RE: [Techtoolslist] Troubleshooting a defective pod
by Martin White 05 Feb '13

05 Feb '13

Actually, please DO top post! Its far, far easier to read on s mobile phone that way :) -----Original Message----- From: John Robertson Sent: 02/02/2013 18:13 To: Technical Tools Mail List Subject: Re: [Techtoolslist] Troubleshooting a defective pod Andre Huijts wrote: > One more thing: > > The manual says to do a ROM test and it gives the addresses in the table but it fails to give the correct signature ? > > Anyone knows it for the Z80 pod ROM V1.1 ? > > > Don't Top Post please! Take the ROM image and pass it through the Signature Generator in the FIDE generator you can download here: http://tech.quarterarcade.com/tech/Fluke/9010A/FIDE.aspx John :-#)# > > > Op 2 feb. 2013, om 15:53 heeft Andre Huijts <a.huijts(a)upcmail.nl> het volgende geschreven: > > >> OK, I recently traded a working 8088 pod (still have two others) for a working Z80 pod. >> I also (temporarily) have a 9010A added to my Fluke stuff. >> >> Now I figured (like the Z80 pod manual suggests) to troubleshoot my defective Z80 pod with the 2nd working one. >> >> The working one self-tests fine on both my 9100A and the 9010A. The defective shows problems on both the 9100A (not recognized please reset) and 9010A. >> >> >> Now....I am confused about the powering up of this set-up. >> >> The normal set-up seems to say to do the following when using a "normal" UUT (no pod): >> >> 1) power off troubleshooter and UUT >> 2) connect pod to troubleshooter >> 3) power on troubleshooter, do self test >> 4) plug in ribbon cable to UUT >> >> So...basically you have to connect the ribbon cable to the UUT while the troubleshooter and POD are powered up ? Feels kind of strange to plug it into the UUT's processor socket while it carries power ? >> >> >> Anyway, next I start reading page 5-12 in the Z80 pod manual and here I get confused: >> >> Under "Prepare to troubleshoot the inoperative pod as follows" it says: >> >> 3) Connect the pod under test to +5V etc. etc......so here they seem to say to DO power up the "UUT (= the defective pod)" BEFORE turning on the power of the troubleshooter. >> >> Step 4) says: Connect a troubleshooter (the 2nd one in my case, the one that will do the troubleshooting) to a 2nd (working) pod, apply power to that troubleshooter and then connect the ribbon cable to the sockpet of the defective pod.... >> >> So basically, this is the other way around of the normal set-up.....which I find strange. >> >> They further cloud things by the next text in BOLD: >> >> "Do not apply or remove any power with ribbon cable connected between second pod and inoperative pod." >> >> So this means I should have to first remove the ribbon connector from the socket of the bad pod before turning any troubleshooter off....right ? >> >> I fear I already did some switching on/off, basically as if it were to be a regular UUT. The good Z80 pod still self-tests OK so I hope I didn't damage anything. >> >> Can someone please tell me what is the right way to do this ? >> >> I did see Power failure messages at some point..... >> >> >> André Huijts >> andre.huijts(a)upcmail.nl >> >> >> -- John's Jukes Ltd. 2343 Main St., Vancouver, BC, Canada V5T 3C9 Call (604)872-5757 or Fax 872-2010 (Pinballs, Jukes, VideoGames) www.flippers.com "Old pinballers never die, they just flip out" _______________________________________________ Techtoolslist mailing list Techtoolslist(a)flippers.com http://seven.pairlist.net/mailman/listinfo/techtoolslist FTP site is: ftp://ttl.arcadetech.org Archive site: http://seven.pairlist.net/pipermail/techtoolslist/

4 6

Z80 pod repair...
by Andre Huijts 04 Feb '13

04 Feb '13

On the Z80 pod I guess U10 is some special IC ? It's listed as "Protector" and it's number is 585992, which "happens to be" the same as the IC number so I guess this is something Fluke custom ? I'm asking because it becomes very hot on the defective Z80 pod...very hot, I guess abnormally hot. André Huijts andre.huijts(a)upcmail.nl _______________________________________________ Techtoolslist mailing list Techtoolslist(a)flippers.com http://seven.pairlist.net/mailman/listinfo/techtoolslist FTP site is: ftp://ttl.arcadetech.org/TTL/Test_Equipment Archive site: http://seven.pairlist.net/pipermail/techtoolslist/

1 0

Re: [Techtoolslist] flippers.com mailing list memberships
by adolfo bustos 02 Feb '13

02 Feb '13

techtoolslist(a)flippers.com Re: flippers.com mailing list memberships keep the subscription for adolfo210511(a)att.net _______________________________________________ Techtoolslist mailing list Techtoolslist(a)flippers.com http://seven.pairlist.net/mailman/listinfo/techtoolslist FTP site is: ftp://ttl.arcadetech.org/TTL/Test_Equipment Archive site: http://seven.pairlist.net/pipermail/techtoolslist/

1 0

Re: Cracking the 9010A ROM signature generator
by Kev 02 Feb '13

02 Feb '13

2 3