- TechToolsList - listserv.classicarcade.com

Housekeeping notice: Change to from_is address format.
by John Robertson via Techtoolslist 14 Feb '16

14 Feb '16

It has come to my attention that at least one person is having trouble posting to the list. I did find this setting explanation: /*from_is_list*//(general): Replace the From: header address with the list's posting address to mitigate issues stemming from the original From: domain's DMARC or similar policies./ /Several protocols now in wide use attempt to ensure that use of the domain in the author's address (ie, in the From: header field) is authorized by that domain. These protocols may be incompatible with common list features such as footers, causing participating email services to bounce list traffic merely because of the address in the From: field. //*This has resulted in members being unsubscribed despite being perfectly able to receive mail.*/ /The following actions are applied to all list messages when selected here. To apply these actions only to messages where the domain in the From: header is determined to use such a protocol, see the //dmarc_moderation_action <https://pairlist7.pair.net/mailman/admin/techtoolslist/?VARHELP=privacy/sen…>//settings under Privacy options... -> Sender filters. / /Settings:/ /No/ /Do nothing special. This is appropriate for anonymous lists. It is appropriate for dedicated announcement lists, unless the From: address of authorized posters might be in a domain with a DMARC or similar policy. It is also appropriate if you choose to use dmarc_moderation_action other than Accept for this list./ /Munge From/ /This action replaces the poster's address in the From: header with the list's posting address and adds the poster's address to the addresses in the original Reply-To: header./ /Wrap Message/ /Just wrap the message in an outer message with the From: header containing the list's posting address and with the original From: address added to the addresses in the original Reply-To: header and with Content-Type: message/rfc822. This is effectively a one message MIME format digest./ // /The transformations for anonymous_list are applied before any of these actions. It is not useful to apply actions other than No to an anonymous list, and if you do so, the result may be surprising. / /The Reply-To: header munging actions below interact with these actions as follows: / /first_strip_reply_to = Yes will remove all the incoming Reply-To: addresses but will still add the poster's address to Reply-To: for all three settings of reply_goes_to_list which respectively will result in just the poster's address, the poster's address and the list posting address or the poster's address and the explicit reply_to_address in the outgoing Reply-To: header. If first_strip_reply_to = No the poster's address in the original From: header, if not already included in the Reply-To:, will be added to any existing Reply-To: address(es). / /These actions, whether selected here or via //dmarc_moderation_action <https://pairlist7.pair.net/mailman/admin/techtoolslist/?VARHELP=privacy/sen…>//, do not apply to messages in digests or archives or sent to usenet via the Mail<->News gateways. / /If //dmarc_moderation_action <https://pairlist7.pair.net/mailman/admin/techtoolslist/?VARHELP=privacy/sen…>//applies to this message with an action other than Accept, that action rather than this is applied/ and I have changed the setting from No to Munge From. I hope that fixes the problem! If anyone know why I should NOT make this change please let me know via email! Thanks, John :-#)# -- How to subscribe or unsubscribe from TTL http://seven.pairlist.net/mailman/listinfo/techtoolslist _______________________________________________ Techtoolslist mailing list Techtoolslist(a)flippers.com https://pairlist7.pair.net/mailman/listinfo/techtoolslist FTP site is: ftp://ttl.arcadetech.org/TTL/Test_Equipment Archive site: http://seven.pairlist.net/pipermail/techtoolslist/

2 1

FS: Fluke 9100A
by Corey Stup via Techtoolslist 14 Feb '16

14 Feb '16

Finally getting some time to spend on rounding up my Fluke 9100 gear. Tony got me setting some of my stuff up today so I wanted to see if the list had any interest in the following: 9100A main unit 68000 CPU 4MB ram 540MB IBM SCSI HD (I'm pretty sure I installed it) 4 port I/O backplate installed video card Upgraded roms to 5.0 EDITOR 6.0 installed on HD Unit is working and tested. Good display and keyboard. Photos available, just email me. Case has some yellowing (they all do) and a scuff across the top. $400 + shipping. PayPal negotiable. USA shipping only please. I also have -003 I/O units with all sizes of DIP plugins and adapters. _______________________________________________ Techtoolslist mailing list Techtoolslist(a)flippers.com https://pairlist7.pair.net/mailman/listinfo/techtoolslist FTP site is: ftp://ttl.arcadetech.org/TTL/Test_Equipment Archive site: http://seven.pairlist.net/pipermail/techtoolslist/

3 2

FS: Z80 Fluke 9010/9100 pod
by Corey Stup via Techtoolslist 14 Feb '16

14 Feb '16

9000A-Z80 pod for 9010 and 9100 series. Self tests 100%. Case is discolored as most of them are. Pins look good. $400 + shipping. PayPal negotiable. Pictures available. Thanks! _______________________________________________ Techtoolslist mailing list Techtoolslist(a)flippers.com https://pairlist7.pair.net/mailman/listinfo/techtoolslist FTP site is: ftp://ttl.arcadetech.org/TTL/Test_Equipment Archive site: http://seven.pairlist.net/pipermail/techtoolslist/

1 0

Re: [Techtoolslist] [Techtassad ] Tek P64dazzling z44
by Jeff Anderson via Techtoolslist 10 Feb '16

10 Feb '16

D5s5 2z z☆zZaz On Feb 6, 2016 5:47 PM, "Ian Eure via Techtoolslist" < techtoolslist(a)flippers.com> wrote: > I purchased a Tek TLA624 logic analyzer a while back, and this thing was > mixed in with the extras. > > After a little research, it seems that it's for an older device, and > doesn't work with the one I have. > > Can anyone here make use of it? > > > _______________________________________________ > Techtoolslist mailing list > Techtoolslist(a)flippers.com > https://pairlist7.pair.net/mailman/listinfo/techtoolslist > FTP site is: ftp://ttl.arcadetech.org/TTL/Test_Equipment > Archive site: http://seven.pairlist.net/pipermail/techtoolslist/ > _______________________________________________ Techtoolslist mailing list Techtoolslist(a)flippers.com https://pairlist7.pair.net/mailman/listinfo/techtoolslist FTP site is: ftp://ttl.arcadetech.org/TTL/Test_Equipment Archive site: http://seven.pairlist.net/pipermail/techtoolslist/

1 0

Fluke 9010 -> 9100 questions & trades
by Ian Eure via Techtoolslist 09 Feb '16

09 Feb '16

Hello, all. I've been reading up, and am considering building out a 9100 setup to replace my 9010. Figured I'd reach out and ask for some advice and see if anyone was interested in working a trade. Couple questions. Can someone enumerate the differences between the 9100A and 9110FT? Looks like: Faster CPU (68030 vs 68000), different PCB layout, and can be expanded to 15(?)mb RAM (vs. 4mb) Anything else? The 9100FT service manual mentions needing to change an EEPROM when upgrading the RAM. Has anyone done this? Is it also necessary for the 9100A? Is the 9132 pod useful for arcade stuff? Looks like it's for 32-bit machines only — maybe you can use one to troubleshoot another 91xx machine? From the manuals, it seems that all the calibration procedures require the probe. I was under the impression that the 91xx probe was identical to the 9010 probe, but I now see that this isn't the case. Can someone speak to how useful the mainframe would be without a probe? Generally, without the harder to find video option, is it a significant upgrade from the 9010a / worth the money? If anyone has 9100 stuff they'd be interested in trading, I have some parts I'd offer. Everything tested/working except as noted. - 9132-024 ROM interface (can't test, fuse & cover missing) - 9132-028 & -032 ROM interfaces (can't test, complete) - 9010a w/serial, working except tape drive - 9010a w/o serial, working except tape drive & push-push buttons don't lock on. - 9010a probe - 2x NOS wrapped Braemar microcassettes - Like new 6809 pod w/manual - 6502 pod - 8080 pod - 6800 pod - 1802 pod - Z80 pod & I think I'd be interested in locating: - 9100A or FT - Video card - Probe - DIP clip modules - 1-2 Parallel IO cards _______________________________________________ Techtoolslist mailing list Techtoolslist(a)flippers.com https://pairlist7.pair.net/mailman/listinfo/techtoolslist FTP site is: ftp://ttl.arcadetech.org/TTL/Test_Equipment Archive site: http://seven.pairlist.net/pipermail/techtoolslist/

4 3

Tek P6444
by Ian Eure via Techtoolslist 06 Feb '16

06 Feb '16

I purchased a Tek TLA624 logic analyzer a while back, and this thing was mixed in with the extras. After a little research, it seems that it's for an older device, and doesn't work with the one I have. Can anyone here make use of it? _______________________________________________ Techtoolslist mailing list Techtoolslist(a)flippers.com https://pairlist7.pair.net/mailman/listinfo/techtoolslist FTP site is: ftp://ttl.arcadetech.org/TTL/Test_Equipment Archive site: http://seven.pairlist.net/pipermail/techtoolslist/

1 0

Data I/O universal calibrator on eBay
by John Robertson via Techtoolslist 05 Feb '16

05 Feb '16

http://www.ebay.com/itm/Data-I-O-910-1071-Universal-Calibrator-/36148351041… Not mine! Only $25! Might be useful to someone here... John :-#)# -- How to subscribe or unsubscribe from TTL http://seven.pairlist.net/mailman/listinfo/techtoolslist _______________________________________________ Techtoolslist mailing list Techtoolslist(a)flippers.com https://pairlist7.pair.net/mailman/listinfo/techtoolslist FTP site is: ftp://ttl.arcadetech.org/TTL/Test_Equipment Archive site: http://seven.pairlist.net/pipermail/techtoolslist/

1 0

Fluke manufacturer supply codes
by Ian Eure via Techtoolslist 02 Feb '16

02 Feb '16

I swear I’ve seen a table that names the manufacturer for a given mfgr supply code in the Fluke service manuals, but of course I can’t find it anywhere. I’m looking for manufacturer 89536, but I’d prefer to know where the table is. _______________________________________________ Techtoolslist mailing list Techtoolslist(a)flippers.com https://pairlist7.pair.net/mailman/listinfo/techtoolslist FTP site is: ftp://ttl.arcadetech.org/TTL/Test_Equipment Archive site: http://seven.pairlist.net/pipermail/techtoolslist/

4 3

Ivan 'Ironman' Stewart's Super Off Road trac pac fluke 9010a script
by John Doe 02 Feb '16

02 Feb '16

this is a code snip form the MAME driver: 59/************************************* 60 * 61 * Master CPU memory handlers 62 * 63 *************************************/ 64 65static ADDRESS_MAP_START( master_map_program, AS_PROGRAM, 8, leland_state ) 66 AM_RANGE(0x0000, 0x1fff) AM_ROM 67 AM_RANGE(0x2000, 0x9fff) AM_ROMBANK("bank1") 68 AM_RANGE(0xa000, 0xdfff) AM_ROMBANK("bank2") AM_WRITE(leland_battery_ram_w) AM_SHARE("battery") 69 AM_RANGE(0xe000, 0xefff) AM_RAM 70 AM_RANGE(0xf000, 0xf3ff) AM_READWRITE(leland_gated_paletteram_r, leland_gated_paletteram_w) AM_SHARE("paletteram") 71 AM_RANGE(0xf800, 0xf801) AM_WRITE(leland_master_video_addr_w) 72 ADDRESS_MAP_END 73 74 75static ADDRESS_MAP_START( master_map_io, AS_IO, 8, leland_state ) 76 ADDRESS_MAP_GLOBAL_MASK(0xff) 77 AM_RANGE(0xf0, 0xf0) AM_WRITE(leland_master_alt_bankswitch_w) 78 AM_RANGE(0xf2, 0xf2) AM_DEVREADWRITE_LEGACY("custom", leland_80186_response_r, leland_80186_command_lo_w) 79 AM_RANGE(0xf4, 0xf4) AM _DEVWRITE_LEGACY("custom", leland_80186_command_hi_w) 80 AM_RANGE(0xfd, 0xff) AM_READWRITE(leland_master_analog_key_r, leland_master_analog_key_w) 81 ADDRESS_MAP_END 82 83 84 85/************************************* 86 * 87 * Slave CPU memory handlers 88 * 89 *************************************/ 90 91static ADDRESS_MAP_START( slave_small_map_program, AS_PROGRAM, 8, leland_state ) 92 AM_RANGE(0x0000, 0x1fff) AM_ROM 93 AM_RANGE(0x2000, 0xdfff) AM_ROMBANK("bank3") 94 AM_RANGE(0xe000, 0xefff) AM_RAM 95 AM_RANGE(0xf800, 0xf801) AM_WRITE(leland_slave_video_addr_w) 96 AM_RANGE(0xf802, 0xf802) AM_READ(leland_raster_r) 97 AM_RANGE(0xf803, 0xf803) AM_WRITE(leland_slave_small_banksw_w) 98 ADDRESS_MAP_END 99 100 101static ADDRESS_MAP_START( slave_large_map_program, AS_PROGRAM, 8, leland_state ) 102 AM_RANGE(0x0000, 0x1fff) AM_ROM 103 AM_RANGE(0x4000, 0xbfff) AM_ROMBANK("bank3") 104 AM_RANGE(0xc000, 0xc000) AM_WRITE(leland_slave_large_banksw_w) 105 AM_RANGE(0xe000, 0 xefff) AM_RAM 106 AM_RANGE(0xf800, 0xf801) AM_WRITE(leland_slave_video_addr_w) 107 AM_RANGE(0xf802, 0xf802) AM_READ(leland_raster_r) 108 ADDRESS_MAP_END 109 110 111static ADDRESS_MAP_START( slave_map_io, AS_IO, 8, leland_state ) 112 ADDRESS_MAP_GLOBAL_MASK(0xff) 113 AM_RANGE(0x00, 0x1f) AM_READWRITE(leland_svram_port_r, leland_svram_port_w) 114 AM_RANGE(0x40, 0x5f) AM_READWRITE(leland_svram_port_r, leland_svram_port_w) 115 ADDRESS_MAP_END 116look at it and you'll find the memory map... ---------------------------------------------------------------------- Message: 1 Date: Mon, 4 Nov 2013 14:05:03 -0500 From: "sales htbs" <sales(a)htbsusa.com> Subject: [Techtoolslist] Ivan 'Ironman' Stewart's Super Off Road trac pac fluke 9010a script To: "'Technical Tools Mail List'" <techtoolslist(a)flippers.com> Message-ID: <003e01ced990$c4893f10$4d9bbd30$@com> Content-Type: text/plain; charset="us-ascii" Subject: Ivan 'Ironman' Stewart's Super Off Road trac pac fluke 9010a script Anyone have a script for Ivan 'Ironman' Stewart's Super Off Road trac pac fluke 9010a script I tried to learn a good board and it did not work I cannot find a memory map for this on quarter arcade I ran the Leland test for bottom board I have 3 board sets that I am working on 1 has the split screen track on top Other 2 were dead Any help would be great Thanks tony @ hi-tech ------------------------------ _______________________________________________ Techtoolslist mailing list Techtoolslist@flippe rs.com http://seven.pairlist.net/mailman/listinfo/techtoolslist End of Techtoolslist Digest, Vol 107, Issue 2 ********************************************* _______________________________________________ Techtoolslist mailing list Techtoolslist(a)flippers.com http://seven.pairlist.net/mailman/listinfo/techtoolslist FTP site is: ftp://ttl.arcadetech.org/TTL/Test_Equipment Archive site: http://seven.pairlist.net/pipermail/techtoolslist/

3 4

Tape for Fluke async clock probe
by Ian Eure 19 Jan '16

19 Jan '16

Does anyone have a good, complete dump of the tape that came along with the async probe for the Fluke 9010a? I have a console with the async clock module, and the probe, but no copy of the tape, which is needed to tun it. I've found a few dumps[1][2][3], but they all appear to be incomplete. Per the manual[4], the tape has two sides, but I don’t see any dumps of side B. All three of the side A dumps are missing programs 12-18, they only have “<BINARY>” placeholders. These seem to be the programs which actually drive the async probe, so it seems unlikely that it would operate without them. Perhaps binary data can’t be transferred via the serial port? I’ll be very annoyed if that’s the case, since working tape drives are rare and I don’t think anybody has figured out how to repair them. [1]: http://www.coinopflorida.com/fluke/9010A%20Arcade%20Scripts/async.s [2]: http://www.coinopflorida.com/fluke/9010A%20Arcade%20Scripts/SA-async.s [3]: http://www.coinopflorida.com/fluke/9010A%20Arcade%20Scripts/ASYNC-R.S [4]: http://arcarc.xmission.com/Test%20Equipment/Fluke/9000/9000A-006%20Async%20… _______________________________________________ Techtoolslist mailing list Techtoolslist(a)flippers.com https://pairlist7.pair.net/mailman/listinfo/techtoolslist FTP site is: ftp://ttl.arcadetech.org/TTL/Test_Equipment Archive site: http://seven.pairlist.net/pipermail/techtoolslist/

3 5