- TechToolsList - listserv.classicarcade.com

Simple use of the 9100
by John Robertson 29 Apr '03

29 Apr '03

I haven't had enough time to look through the manuals (nasty things - written in Fluke-Speak) but I was wondering if there are simple tests in the 9100 that compare to the 9010A. For example the ROM test (one sets the hex area to check) does it produce a signature or checksum? RAM test? Learn? I know I should read the books, but, heck, I'm hoping someone here with more experience in this series can give a couple of quick guidelines... John :-#)#

1 0

6809/6809E pod documentation?
by James S. Bright 27 Apr '03

27 Apr '03

Anyone have this pod's documentation? I didn't see it on the FTP site. Specifically I'm looking for the Status/Control line mapping. Thanks. JB --James Bright www.QuarterArcade.com Restored Arcade Games for your Home

1 0

Re: TI Data book wrong?
by Dave Langley 27 Apr '03

27 Apr '03

At 05:37 pm 26 04 2003, you wrote: >Just got the new Pocket data book from TI, nice book BUT is the dwg for >74157 wrong (or am I reading it wrong?) > >Page 218 doesn't look right to me. Nor to me! I pulled out my TI Databook vol 1 (1985) and the diagram in that book is the same as the 74158 (Page 220 of the new TI book) but the outputs 1Y to 4Y are not inverted for the '157. So that diagram is completely wrong, but interestingly the truth table is correct. I guess the clue is that the inputs and outputs from the diagram don't relate to the truth table! I can scan the pages from my book if you like. Dave Langley www.robotron-2084.co.uk

1 0

TI Data book wrong?
by Kev 26 Apr '03

26 Apr '03

Just got the new Pocket data book from TI, nice book BUT is the dwg for 74157 wrong (or am I reading it wrong?) Page 218 doesn't look right to me. Thanks, Kev

2 1

OT? Tek 1241 logic analyzer manuals on CD
by A218＠aol.com 25 Apr '03

25 Apr '03

2 1

9010A, Not sure what this means...
by James S. Bright 20 Apr '03

20 Apr '03

Working on a Centipede (6502 based). RAM test (Short or Long) on RAM that I think is good, I get "RAM DCD ERR @ 0000 BIT 0". I'm not sure what this means. I've tested the buffer chips (data and address) and they appear to be okay. When I run custom tests (reading and writing AA/55), the RAM seems okay. Can anyone elaborate on this error message? The manual didn't really help out. I'm not exactly sure what to do next with this board. (This board doesn't play blind, and nothing appears on monitor.) TIA. JB --James Bright www.QuarterArcade.com Restored Arcade Games for your Home

3 4

RE: 9010A, Not sure what this means...
by James S. Bright 19 Apr '03

19 Apr '03

THANKS! Write @ 0 = FF Write @ 1 = 00 Read @ 0 return F0 I need to update my manual RAM checker too. JB > -----Original Message----- > From: James S. Bright [mailto:james@quarterarcade.com] > Sent: Saturday, April 19, 2003 7:34 PM > To: 'techtoolslist(a)flippers.com' > Subject: RE: 9010A, Not sure what this means... > > > > Thanks. This is very helpful... > > JB > > --James Bright > www.QuarterArcade.com > Restored Arcade Games for your Home > > > > -----Original Message----- > > From: Mark Shostak (DOS) [mailto:shostak@augustmail.com] > > Sent: Saturday, April 19, 2003 7:27 PM > > To: James S. Bright; techtoolslist(a)flippers.com > > Subject: Re: 9010A, Not sure what this means... > > > > > > If I read your question correctly, > > > > It's complaining about an address decoding error, > > specifically with bit A0. So, it found that when it wrote a > > value to an address, then changed bit A0, the value it wrote > > to the previous address appeared at this other address. > > > > Try your manual test again: > > write 55 to 0 (and read back) > > write AA to 1 (and read back) > > read 0 again and see if it's 55 or AA > > also try it the other way (if writes to loc 0 appear at loc 1) > > > > That's the basic idea. Bit 0 is about the easiest one you > > could have hoped for to learn on. Hope that helps. > > > > -Mark > > > > > > > > > > > > > Working on a Centipede (6502 based). > > > > > > RAM test (Short or Long) on RAM that I think is good, I get > > "RAM DCD > > > ERR @ 0000 BIT 0". I'm not sure what this means. I've tested the > > > buffer chips (data and address) and they appear to be okay. > > When I run > > > custom tests (reading and writing AA/55), the RAM seems okay. Can > > > anyone elaborate on this error message? The manual didn't > > really help > > > out. I'm not exactly sure what to do next with this board. > > > > > > (This board doesn't play blind, and nothing appears on monitor.) > > > > > > TIA. > > > > > > JB > > > > > > --James Bright > > > www.QuarterArcade.com > > > Restored Arcade Games for your Home > > > > > > > > > > > > > > > >

1 0

Tape drive repair parts for Fluke 9010A last call
by A218＠aol.com 19 Apr '03

19 Apr '03

1 0

Re: So I got myself a Fluke 9010a and...
by John Robertson 17 Apr '03

17 Apr '03

This is the RESET showing up...find the Watchdog Disable test point and connect it to ground. Then try your tests again. This is covered in the 9010A Operators manual, copies are available in PDF if you don't have a hard copy... John :-#)# At 07:48 PM 09/04/2003 -0500, Joe wrote: > So I got myself a Fluke 9010a and I power it up, pod passes self test >just fine.. I plug the beast into the Gravitar CPU socket, all good so >far. Power up the 9010a and then the Gravitar. Now I do a RAM SHORT test >from 0000-07FF and get the following error "Active Force Line @ >0000-Loop?" > >So, what am I doing wrong? The Gravitar board I'm using is a known good >board, so this must be operator error, right? > >Any help or suggestions will be appreciated. > >Thanks, >JB

3 3

So I got myself a Fluke 9010a and...
by Joe 10 Apr '03

10 Apr '03

So I got myself a Fluke 9010a and I power it up, pod passes self test just fine.. I plug the beast into the Gravitar CPU socket, all good so far. Power up the 9010a and then the Gravitar. Now I do a RAM SHORT test from 0000-07FF and get the following error "Active Force Line @ 0000-Loop?" So, what am I doing wrong? The Gravitar board I'm using is a known good board, so this must be operator error, right? Any help or suggestions will be appreciated. Thanks, JB

1 0