- TechToolsList - listserv.classicarcade.com

Sencore CR31A Setup Book
by Mark Hooks 04 Oct '04

04 Oct '04

2 1

Re: A quick apology and questions about debuging Cloak & Dagger boards with a fluke 9010
by John Robertson 03 Oct '04

03 Oct '04

2 1

Removing bounces...
by John Robertson 28 Sep '04

28 Sep '04

I've had a few folks seem to vanish from the face of the earth (or at least email world), if anyone knows these people and can let them know I've had to delete them... Bounces ("no one here by that name"): kyle.simons(a)marconi.com mhooks10(a)cs.com pc2jamma(a)SAO.terra.com.br dale(a)shoretel.com Refusals: Deferred: Connection refused by bombjack.freeserve.co.uk.servepower.com Thanks! John :-#)# -- How to subscribe or unsubscribe from TTL To do either you send email to "MajorDomo(a)flippers.com" and in the body you state either "Subscribe techtoolslist" or "Unsubscribe techtoolslist", note that the Subject is "" (Blank)... FTP site is: ftp://ftp.flippers.com/pub/TTL/ If you ever want to (un)subscribe yourself with TTL, you can send mail to: <Majordomo(a)flippers.com> with the following command in the body of your email message: (un)subscribe techtoolslist or from another email account, besides xxx(a)yyy.com: (un)subscribe techtoolslist xxx(a)yyy.com

1 0

Fluke 9010a Tape Drive
by Rodger Boots 28 Sep '04

28 Sep '04

2 1

Instruction video 9010a
by MyPearl 20 Sep '04

20 Sep '04

1 0

Pat 9000 restore
by Philip 17 Sep '04

17 Sep '04

2 3

Pat 9000 restore
by Philip 16 Sep '04

16 Sep '04

1 0

Fluke 9010a Tape Drive
by MyPearl 13 Sep '04

13 Sep '04

2 1

Micro Concepts BoardWalker 103
by Tom Leffingwell 31 Aug '04

31 Aug '04

I recently happened across a BoardWalker 103, I don't suppose anyone has a manual for it? It is missing the test clip unfortunately. Does anyone know the difference between the 103 and 101? I was hoping to build a replacement test clip as well if I could get pinout information on the test clip connector. There are more pins on the test clip connector than there are holes in the ZIF socket, so I'm not exactly sure what's going on. Anyway, any info is greated appreciated, as I know very little about it. Thanks, -Tom If you ever want to (un)subscribe yourself with TTL, you can send mail to: <Majordomo(a)flippers.com> with the following command in the body of your email message: (un)subscribe techtoolslist or from another email account, besides xxx(a)yyy.com: (un)subscribe techtoolslist xxx(a)yyy.com

1 0

Pod pins
by Phil Morris 14 Aug '04

14 Aug '04

What's the recommended/best way to replace broken pins on the main CPU plug on a pod? Pin 40 on my 6502 pod has just broken off (still seems to work fine though and passes the Bus Test). I have in fact been using a 'sacrificial socket' to try and avoid this, but this just came off and bent the pin so badly that it broke off. It's broken off too close to the plastic to realistically attach another pin. Ta, Phil If you ever want to (un)subscribe yourself with TTL, you can send mail to: <Majordomo(a)flippers.com> with the following command in the body of your email message: (un)subscribe techtoolslist or from another email account, besides xxx(a)yyy.com: (un)subscribe techtoolslist xxx(a)yyy.com

2 1