April 2017 - TechToolsList - listserv.classicarcade.com

BK Precision 560 V3.10 ROMs
by Ian Eure 15 Apr '17

15 Apr '17

Here are the dumps I made. I’ve verified these in two other 560s. Install is the same as for V3.00, burn to four 2764s & install in the IC4-IC7 sockets. I have no idea what’s different from V3.00. https://dl.dropboxusercontent.com/u/6120067/bk560-v310.zip _______________________________________________ Techtoolslist mailing list Techtoolslist(a)flippers.com https://pairlist7.pair.net/mailman/listinfo/techtoolslist FTP site is: ftp://ttl.arcadetech.org/TTL/Test_Equipment Archive site: http://seven.pairlist.net/pipermail/techtoolslist/

3 3

Fluke trading post
by Ian Eure 08 Apr '17

08 Apr '17

Have the following: Fluke 9010a, working except the tape drive (rotten belts like usual). Has serial + uncommon async signature option, and dodgy but working probe. Another Fluke 9010a logic probe, in good working condition. Fluke 9132-024 and -028 ROM modules. Fluke 9100 clock module. Failed calibration, fuse is fine, maybe a broken lead? Fluke 9100 40mb SCSI hard disk (Quantum ProDrive ELS 42. Working pull with OS loaded (I forget what version), this can be used to upgrade a stock 20MB 9100A. I’m looking for: Fluke 9100 Programmer’s Manual Fluke 9100 TL/1 Reference Manual Z8000 pod 9132 RAM modules (x3) 9100 IO module, ideally I’d like a vector module. Happy to work trades +- cash or maybe other test equipment. _______________________________________________ Techtoolslist mailing list Techtoolslist(a)flippers.com https://pairlist7.pair.net/mailman/listinfo/techtoolslist FTP site is: ftp://ttl.arcadetech.org/TTL/Test_Equipment Archive site: http://seven.pairlist.net/pipermail/techtoolslist/

4 6

Sencore cm2220 info needed.
by Rich Drewniak via Techtoolslist 07 Apr '17

07 Apr '17

Does anyone have any software/manuals for a sencore CM2220? Thanks. _______________________________________________ Techtoolslist mailing list Techtoolslist(a)flippers.com https://pairlist7.pair.net/mailman/listinfo/techtoolslist FTP site is: ftp://ttl.arcadetech.org/TTL/Test_Equipment Archive site: http://seven.pairlist.net/pipermail/techtoolslist/

2 1

FS: BK 560 bench IC tester/comparator
by Ian Eure 04 Apr '17

04 Apr '17

Selling my extra BK 560. This is running v3.10, which is newer than any publicly available dumps. I'll share the images after it sells. Everything works as expected. Comes with a 20 pin DIP clip for building the in-circuit test cable. Asking price is $350 shipped in the CONUS. Open to trades for a Z8000 pod or Fluke 9100 stuff. Photos here. The one of the factory EPROMs is to show that v3.10 is authentic. The machine I'm selling comes with the white labeled copies. https://imgur.com/a/SV8y8 _______________________________________________ Techtoolslist mailing list Techtoolslist(a)flippers.com https://pairlist7.pair.net/mailman/listinfo/techtoolslist FTP site is: ftp://ttl.arcadetech.org/TTL/Test_Equipment Archive site: http://seven.pairlist.net/pipermail/techtoolslist/

3 3

Fluke 9010 and pole position memory map
by David Shoemaker 03 Apr '17

03 Apr '17

Looking at the memory map the schematics list a single memory map for CPU 1 & 2 (Z8002's) and another memory map for CPU 3 (Z80). I am trying to understand just how the memory is map. Can the Z80 actually get to all the ram onboard? This would make using the Z80 pod to do memory work reasonable. Vs having to find that z8002 pod. But the address space doesn't make a lot of sense. _______________________________________________ Techtoolslist mailing list Techtoolslist(a)flippers.com https://pairlist7.pair.net/mailman/listinfo/techtoolslist FTP site is: ftp://ttl.arcadetech.org/TTL/Test_Equipment Archive site: http://seven.pairlist.net/pipermail/techtoolslist/

2 2

Re: [Techtoolslist] 9010 ram pattern error?
by Tony Jones 03 Apr '17

03 Apr '17

The overview of what the tester is doing in the pattern test is on that page of the manual. For the reported failing address (long should report this as well as the BTS discrepancy) what is reported for short, or manual write/read? On Apr 2, 2017 7:48 PM, "David Shoemaker" <davids(a)oz.net> wrote: Looping results in an unstable OK / Err condition. -----Original Message----- From: Techtoolslist [mailto:techtoolslist-bounces@flippers.com] On Behalf Of Tony Jones Sent: Sunday, April 2, 2017 6:34 PM To: Technical Tools Mail List <techtoolslist(a)flippers.com> Subject: Re: [Techtoolslist] 9010 ram pattern error? On Sun, Apr 2, 2017 at 5:46 PM, David Shoemaker <davids(a)oz.net> wrote: > I have never been able to wrap my head around the pattern error. The long test is looking for pattern sensitive errors (nearest neighbor). What happens if you LOOP (see 4H-11 in the operators manual). I've seen similar on a (non arcade) board with a bad bus transceiver but it can also indicate a fault in the RAM itself. _______________________________________________ Techtoolslist mailing list Techtoolslist(a)flippers.com https://pairlist7.pair.net/mailman/listinfo/techtoolslist FTP site is: ftp://ttl.arcadetech.org/TTL/Test_Equipment Archive site: http://seven.pairlist.net/pipermail/techtoolslist/ _______________________________________________ Techtoolslist mailing list Techtoolslist(a)flippers.com https://pairlist7.pair.net/mailman/listinfo/techtoolslist FTP site is: ftp://ttl.arcadetech.org/TTL/Test_Equipment Archive site: http://seven.pairlist.net/pipermail/techtoolslist/ _______________________________________________ Techtoolslist mailing list Techtoolslist(a)flippers.com https://pairlist7.pair.net/mailman/listinfo/techtoolslist FTP site is: ftp://ttl.arcadetech.org/TTL/Test_Equipment Archive site: http://seven.pairlist.net/pipermail/techtoolslist/

2 2

9010 ram pattern error?
by David Shoemaker 03 Apr '17

03 Apr '17

Have a pole position board using z80qt pod. Doing an alpha memory long ram test. Getting a pattern error. "Data was FE not FF". How do I use this information to figure out what the part which is failing is? I have never been able to wrap my head around the pattern error. Thanks, David _______________________________________________ Techtoolslist mailing list Techtoolslist(a)flippers.com https://pairlist7.pair.net/mailman/listinfo/techtoolslist FTP site is: ftp://ttl.arcadetech.org/TTL/Test_Equipment Archive site: http://seven.pairlist.net/pipermail/techtoolslist/

3 4

FT: Fluke 9100 repro video card pcb
by Tony Jones 02 Apr '17

02 Apr '17

These cards came up a while ago on this thread (https://goo.gl/pNL7Uz) which went rapidly off the rails. I bought all of Andrew's extra cards last year when I was back in the UK and distributed them to the US people on the thread who had expressed interest. I kept two for myself. Since I also have two original 9100 video cards, I'd be willing to trade the two repro pcbs (unpopulated) pic of pcb: https://s20.postimg.org/n5eve84sd/IMG_8619.jpg I'm looking for: original 9100 keyboard: https://s20.postimg.org/oyhs2jpz1/Fluke_9100_Keyboard.jpg Fluke 900 interface buffer: https://s20.postimg.org/9o1gh1xkt/20160920_101745.jpg Fluke 9132FT ROM adapters: https://s20.postimg.org/icqcut83h/9132_FT_ROM_adapters.jpg _______________________________________________ Techtoolslist mailing list Techtoolslist(a)flippers.com https://pairlist7.pair.net/mailman/listinfo/techtoolslist FTP site is: ftp://ttl.arcadetech.org/TTL/Test_Equipment Archive site: http://seven.pairlist.net/pipermail/techtoolslist/

1 0

Re: [Techtoolslist] Fluke trading post
by Tony Jones 02 Apr '17

02 Apr '17

On Apr 2, 2017 11:36 AM, "Ian Eure" <ieure(a)icloud.com> wrote: I’m looking for: Fluke 9100 Programmer’s Manual Fluke 9100 TL/1 Reference Manual Z8000 pod 9132 RAM modules (x3) 9100 IO module, ideally I’d like a vector module. I have three -017 vector modules, I'd trade one for two -003 parallel modules. z8000 pod seems flavor of the day. _______________________________________________ Techtoolslist mailing list Techtoolslist(a)flippers.com https://pairlist7.pair.net/mailman/listinfo/techtoolslist FTP site is: ftp://ttl.arcadetech.org/TTL/Test_Equipment Archive site: http://seven.pairlist.net/pipermail/techtoolslist/

1 0

Long shot but looking for z8000 pod
by David Shoemaker 02 Apr '17

02 Apr '17

Plus the z8002 adapter so I can work on some Pole Position boards. Anyone have one they are willing to part with? Thanks, David _______________________________________________ Techtoolslist mailing list Techtoolslist(a)flippers.com https://pairlist7.pair.net/mailman/listinfo/techtoolslist FTP site is: ftp://ttl.arcadetech.org/TTL/Test_Equipment Archive site: http://seven.pairlist.net/pipermail/techtoolslist/

1 0